Physics for swimmers, coaches and parents – Frontal drag

Most sports take place in air, where drag forces apply but are not nearly as detrimental to performance as they are in swimming. With the density of water being 784 times greater than air, any errors we make in our body position or stroke mechanics are compounded at almost any speed, but even more so at higher speeds. However, we don’t have to be going very fast at all in water for these drag forces to ruin our day. The faster we swim, the bigger price we pay for our mistakes. Frontal drag is enemy #1 of the swimmer. There is no mercy in the water.

 

There are four factors that determine how much frontal drag will slow a swimmer down. The first is position. Is the swimmer underwater or on the surface? The second is the cross-sectional surface area of the swimmer moving forward. How large is the swimmer? What is the body angle? Are the legs and arms protruding out too far? Is the head too high? The third is the surface characteristic of the swimmer, including the suit, cap and goggles. How slippery is the swimmer? The fourth, and most important, is the swimmer’s speed. How fast is he or she moving in the water?

 

There are three different types of frontal drag forces that can slow a swimmer down, and they are all important. The first and most profound is pressure or form drag which occurs as a result of two important facts we see in good swimmers. First, swimmers are non-streamlined objects, even in the best position they can achieve. Second, good swimmers are in water and travel at speeds approximating 2 meters/second or higher. The physical shape of a swimmer (surface area moving forward), the medium of water, and the speed of the swimmer in the water are factors that determine what is called the Reynold’s number. This determines the flow characteristics around the moving swimmer. At the Reynold’s number of a good swimmer wearing a tech suit, the flow of water around him/her will change from laminar (smooth, at the head and shoulders) to transitional (separated from the boundary a foot or so behind the head and shoulders) to turbulent (somewhere near the waist). As the fluid transitions from the boundary of the swimmer’s body to a turbulent state, it then forms a vortex or slipstream behind the swimmer. The difference between the higher pressure at the head of the swimmer and the lower pressure behind the swimmer in the slipstream is what determines the pressure drag.

 

The second drag force is caused by friction. Friction occurs as a result of molecules rubbing against each other as an object moves through a medium; in this case, water. In general, the rougher the object (swimmer), the more friction. The smoother or slicker the object (swimmer), the less friction. Thus, the friction of a swimmer is largely determined by the surface characteristics of the swimmer; the cap, the skin, the goggles and the suit.

 

Third type of drag force is called surface or wave drag. It occurs as a result of the swimmer being partly in the water (submerged) and partly out of the water. Virtually all of the wave drag of a swimmer occurs from the front end of the swimmer’s body (head and shoulders).

 

In a study done in 2004, Mollendorf et al determined the contribution of all three types of frontal drag forces on swimmers while being towed at various speeds in a fixed, streamlined position (passive drag forces).[1] When low friction (high tech) suits were worn, and at approximately race speed for elite swimmers, they found that pressure drag forces accounted for about 50% of the total drag force, while wave drag forces and friction each accounted for about 25% of the total drag force. The total frontal drag forces were about three times greater at 2 m/sec (race speed) than they were at 1 m/sec. When low tech suits were worn, friction was a greater contributor to total drag than pressure or wave drag.

 

The reason that the swimmer’s speed is the most important factor in determining frontal drag is that all three types of drag forces are exponentially related to the swimmer’s speed. Both pressure drag and friction are proportional to the square of the swimmer’s speed, while wave drag is proportional to the fourth power of the swimmer’s speed. From this observation, we can conclude the following:

 

  1. All three types of frontal drag are important and need to be reduced as much as possible
  2. Small changes in a swimmer’s shape or position, cap and suit can have profound impacts on frontal drag at race speed
  3. Getting under water is desirable (eliminating wave drag) whenever possible while in a relative streamline position at race speed
  4. The stronger and faster a swimmer becomes, the more important technique becomes (the frontal drag forces at 2 m/sec are about three times greater than at 1 m/sec)

 

This week in Lanes 2, 3  and 4, you will receive the Race Club webisode featuring our favorite way to streamline in order reduce frontal drag. We hope you enjoy.

 

 

[1] Mollendorf, J.C., Termin A.C., Oppenheim E., and Pendergast D.R., Effect of Swim Suit Design on Passive Drag, MEDICINE & SCIENCE IN SPORTS & EXERCISE 0195-9131/04/3606-1029

4 responses to “Physics for swimmers, coaches and parents – Frontal drag”

  1. williamschris40@yahoo.com says:

    I’m a lane three member but cannot access this article. Can you help me out?

    Chris Williams

  2. swimsmart@yahoo.com says:

    what about the length of the vessel (how tall the swimmer is)? how does that effect swim speed?

    • garysr says:

      Probably more important is the length of the arms…which is often correlated with the length of the body. Longer levers (arms) can produce more propulsion per stroke. Large girth of the body is what you don’t want.

Leave a Reply